Truck Tire Repair Fargo ND

This page provides relevant content and local businesses that can help with your search for information on Truck Tire Repair. You will find informative articles about Truck Tire Repair, including "Truck tire repair saves money". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Fargo, ND that can help answer your questions about Truck Tire Repair.

Dans Service Center Inc
(701) 356-4100
3910 2nd Avenue South, # C
Fargo, ND
Services
Auto Parts,Oil Change and Lube,Alignment Repair,Auto Repair,Truck Repair

Pit Stop
(701) 282-2500
301 40th St S
Fargo, ND
Services
Auto Parts,Oil Change and Lube,Auto Repair,Truck Repair

Teds Northport Tesoro
(701) 232-8304
2740 Broadway N
Fargo, ND
Services
Auto Parts,Oil Change and Lube,Auto Repair,Truck Repair

Dans Service Center Inc
(701) 356-4100
3910 2nd Avenue South, # C
Fargo, ND
Services
Auto Parts,Oil Change and Lube,Alignment Repair,Auto Repair,Truck Repair

Bergers Body and Glass
(701) 642-3773
17915 Highway 13
Wahpeton, ND
Services
Auto Parts,Oil Change and Lube,Auto Repair,Interior Cleaning,Interior Repair,Truck Repair

OK Tire Stores Inc
(701) 237-6525
2224 Main Avenue
Fargo, ND
Services
Clutch Repair,Truck Service Station

Exhaust Pros
(701) 293-9600
2118 Main Avenue
Fargo, ND
Services
Mufflers Repair,Truck Service Station

Dans Service Center Inc
(701) 282-7800
413 Main Avenue West
West Fargo, ND
Services
Auto Parts,Oil Change and Lube,Alignment Repair,Auto Repair,Truck Repair

Quality Service and Repair
(701) 663-5596
1311 1st St NE
Mandan, ND
Services
Auto Parts,Oil Change and Lube,Auto Repair,Truck Repair

Olsons Repair
(701) 525-6391
4 Main Street
Karlsruhe, ND
Services
Auto Parts,Oil Change and Lube,Auto Repair,Fuel Injection Repair,Truck Repair

Truck tire repair saves money

Tires are one of the largest equipment expenses facing fleet equipment managers, so it's important to get the longest life possible out them. Retreading is one way that many fleets prolong the life of their tires.

But many times a tire will encounter road debris that damages the tread section before the tire is ready to be retreaded. In those cases, fleets can prolong the tire's life by repairing the tire puncture.

But not every tire that has been damaged is a good candidate for a repair, according to Patch Rubber Co. For example, tires that incur punctures or damage to the sidewall and the shoulder area are not candidates for repair. Other limiting factors are if there is 2/32-inch or less of tread on any two adjacent tread grooves; if the tire cord or steel belt is exposed; or if there are flex breaks or severe sidewall abrasions.

If a puncture occurs in the repairable area of the tread and it does not exceed three-eights of an inch in size, fleets can safely repair that tire and return it to service. According to Patch Rubber Co., here are the steps to take to repair the tread puncture:

1. Locate the injury and circle it with a tire crayon. Consult the warning on the back cover for the repairability of tires. Do not invert radial tires.

2. Remove the foreign object and probe the injury with an awl to determine the angle of penetration.

3. Clean the area around the injury with cleaner fluid and a scraper.

4. Using a low-speed (500 to 700 RPM) drill and a carbide butter, ream the injury following the angle of penetration from inside of the tire. Use proper eye protection.

5. Remove the poly from the plug stem. Hook the plug stem onto the wire puller. Coast the entire plug with fast-drying self-vulcanizing cement.

6. While the cement is still wet, push the wire puller through the injury from the inside of the tire. Grasping the wire, use a steady pull until .5 inch of the gray rubber on the plug is exposed outside the tire.

7. Using a flexible knife, cut the plug on the inside of the tire 1/8-inch above the innerliner. Be careful not to stretch the plug when cutting.

8. Making sure the bead arrows of the repair unit are pointing to the beads, center the repair unit over the injury. Use a tire crayon and outline an area .5 inch larger than the repair unit.

9. Use a low-speed (maximum 5,000 RPM) buffer and a buffing rasp to buff the plug and the outlined innerliner area. Be careful not to buff through the innerliner.

10. Use a vacuum to remove the buffing dust.

11. Apply a light coat of rubber cleaner fluid to the buffed area, scrape it clean and allow it to dry.

12. Apply an even coat of fast-dry self-vulcanizing cement to the entire buffed area. Allow cement to dry until tacky. Never use blow dryers, compressed air or heat lamps to quicken drying. Drying time is affected by temperature and humidity.

13. When cement is dry, partially remove the poly backing from the patch leavi...

Click here to read more from Fleet Equipment

© Copyright 2011 Babcox Media, Inc. All Rights Reserved
3550 Embassy Parkway, Akron, OH 44333
330-670-1234
(FAX) 330-670-0874