Cooling System Repair Cedar City UT

This page provides relevant content and local businesses that can help with your search for information on Cooling System Repair. You will find informative articles about Cooling System Repair, including "Pressure-checking cooling systems and radiator caps" and "Cooling Systems: old maintenance problems, new technology". Below you will also find local businesses that may provide the products or services you are looking for. Please scroll down to find the local resources in Cedar City, UT that can help answer your questions about Cooling System Repair.

Juan Ortega's Auto Inc
(435) 238-7808
731 E Midvalley Rd
Enoch, UT
Hours
Monday 8:00 AM - 5:00 PM
Tuesday 8:00 AM - 5:00 PM
Wednesday 8:00 AM - 5:00 PM
Thursday 8:00 AM - 5:00 PM
Friday 8:00 AM - 5:00 PM
Saturday Closed
Sunday Closed
Memberships and Certifications
Certifications : ASE, Napa 12 Month/12,000 Miles
Services
Air Conditioning/Heating, Alignment, Alternator, Battery, Belts & Hoses, Catalytic Converter, Clutch Cylinder, Cooling System, Diagnostics, Drive Belt, Electrical System, Exhaust Systems, Filters & Fluids, Fuel Injector, Fuel Pump, Fuel System, Head Gasket, Headlight/Headlamp, High Performance Service, Ignition, Inspection, Muffler, Oil Pan, Oil Pump, Oxygen Sensor, Parts, Radiator, Restoration Service, Shocks & Struts, Spark Plugs, Starter, Thermostat, Timing Belt, Tune-Up, Water Pump, Window M
Service Types and Repair
Acura, Aston Martin, Audi, Auto Clutch, Auto Drivetrain, Auto Engine, Auto Interior, Auto, Bentley, BMW, Buick, Cadillac, Chevrolet, Chrysler, Classic Car, Diesel Engine, Dodge, Emergency Auto, Exotic Car, Fiat, Ford, GMC, Harley Davidson, Honda, Hyundai, Infiniti, Isuzu, Jaguar, Jeep, Kia, Land Rover, Lexus, Lincoln, Lotus, Mazda, Mercedes Benz, Mitsubishi, Motorcycle/ATV, Nissan, Oldsmobile, Pontiac, Porsche, RV/Bus, Saab, Saturn, Small Engine, Subaru, Suzuki, Toyota, Truck, Volkswagen, Volvo

Jiffy Lube
(435) 865-1111
707 S MAIN ST
CEDAR CITY, UT
Hours
Sun: CLOSED
Mon-Sat: 8:00 AM-6:00 PM

Tri State Motors
(435) 586-6563
298 S Main Street
Cedar City, UT
Services
Fuel Injection Repair,Radiator Repair,SUV Repair,Tune up Repair,Used Car Dealers,Auto Dealers

Wal-Mart Supercenter
(435) 865-2792
1330 S Providence Center Dr
Cedar City, UT
Services
Car Washes, Car Detailing, Tire Shops

Royal Express Transmission
(435) 867-0223
590 North Main Street
Cedar City, UT
 
St. George Transmission 2
(435) 865-1100
1130 North Main Street
Cedar City, UT
 
Desert Pines Tire
(435) 586-6035
1001 S Main St
Cedar City, UT
Services
Car Washes, Car Detailing, Tire Shops

Jiffy Lube
(435) 867-9439
1240 Sage Dr
Cedar City, UT
Services
Oil Change and Lube, Automotive Transmission

Auto Moto
(888) 865-7770
1212 North Airport Road
Cedar City, UT
Services
SUV Repair,Van Dealers,Used Truck Dealers

Southern Performance Transmissions
(435) 865-9919
1130 North Main Street
Cedar City, UT
 

Cooling Systems: old maintenance problems, new technology

Manufacturers have addressed many cooling system problems, but regular maintenance is still important

Heat is one thing diesel engines produce in abundance. The role of the engine and truck design engineer is to take that heat and do something useful with as much of it as possible and get rid of the rest in the most efficient way.

The heat of combustion in diesels is roughly divided three ways. One third produces useful power. Another third goes out through the exhaust system, and the final portion needs to be taken out by the cooling system. Note the portion that goes out with the exhaust. Now remember when EGR was first introduced, and engineers started taking some of those heated exhaust gases and returning them to the engine.

Engineers, of course, understood what was happening, so it was no surprise that cooling systems would be stressed. As a result, cooling systems were beefed up, but in many cases, not enough. It was when the first EGR-equipped trucks went into service that we started hearing stories of melted plastic parts from never-before-seen underhood temperatures. Thankfully, such horror stories are, by and large, a thing of the past.

Truck manufacturers and fleet managers have done an excellent job keeping problems in check, but many of the remedies have increased costs and some are costing fuel mileage. Design engineers have found ways to better manage the airflow through the radiator and over the engine, but underhood temperatures are still high and components are still stressed. For example, when fan clutches were first introduced, they ran only 3% or 4% of the time. Now they’re running as much as 80% of the time. Fan clutches are certainly better now with higher quality steel in the shafts and better bearings, but emphasis must still be placed on system maintenance. It is the case that even a minor reduction in cooling system function can cause a diesel engine to self-destruct.

While designs have improved, cooling systems are still too often overlooked during routine PM inspections. Darry Stuart, president and CEO of DWS Fleet Management Service, says, “Industry-wide, maintenance is not being performed on cooling systems as it should be. For example, I find upwards of half of the radiator caps in service are defective. They need to be checked during PM inspections and replaced when necessary.”

Pressurize at every PM

Engineers from the National Automotive Radiator Service Association (NARSA) note that the mileage on a vehicle is not as big a factor in cooling system maintenance requirements as is the vehicle’s age. An aging vehicle has been exposed over time to environmental factors that can harm a cooling system–– ocean air, road salt, debris and other chemicals tend to deteriorate the system.

The best way to check a system for small leaks is to pressurize it before making an inspection. In many cases a small leak might not even be noticed because of ...

Click here to read more from Fleet Equipment

Pressure-checking cooling systems and radiator caps

Stuart practices:
The reason fleets need to regularly pressure check on cooling systems and radiator caps at each PM is to avoid coolant loss and potential over-heating and shut-down issues. You need to pressurize the system to a minimum of 18 lbs. at each scheduled PM as well as the cap to its release pressure stamped on the cap. Be careful of replacement radiator caps; they should be checked before installation. There can be undetermined invisible coolant loss, as well as lower boiling points, and maybe film boiling.

Coolant can evaporate externally dripping on a hot engine -- these small amounts will escape undetected. If you are adding engine coolant at the fuel island, truck stop or in the shop, something is wrong. Make this simple procedural check a part of your preventive maintenance routine. When is the last time you added coolant to your own personal vehicle? After all, it is a closed system!         

DWS Fleet Management website:  www.darrystuart.co...

Click here to read more from Fleet Equipment

© Copyright 2011 Babcox Media, Inc. All Rights Reserved
3550 Embassy Parkway, Akron, OH 44333
330-670-1234
(FAX) 330-670-0874